1. Place the copying machine away from moisture, water, and direct sunlight. Prevent heat, dust, and a good ventilation environment are suitable for copier placement.
2. The copier should use a stable voltage. It is recommended to use the socket directly against the wall.
3. The photocopier should be preheated for half an hour before use, which can make the inside of the copier dry, which is beneficial to the effect of copying.
4. Use of the copier According to the instructions for use, read the instructions carefully before copying. Different copying requirements require careful operation according to the function description of the copier.
5. When copying, keep the copier's glass platen clean, scratch-free, and can't have spots such as correction fluid and fingerprints to avoid unclear copying and affect the copying effect.
6. After each use of the copier, be sure to wash your hands in time to eliminate any damage to the body caused by residual dust on your hands.
7. When you find that the effect of copying has a heavy shadow, you may need to clean the lens on the copier.
8. The user should promptly add toner to the copier when the copier panel displays the red light plus powder signal. If the toner is not added in time, it may cause the copier to malfunction or produce powder-impact noise. When adding toner, shake the toner and follow the instructions. Do not use substitute powder (pseudo-powder), otherwise it will cause problems such as flying powder, bottom ash, and shortening the service life of the carrier. Moreover, due to the high rate of waste powder it produces, the actual copy quantity is less than 2/3 of the true powder. .
9. Add paper to the copier. Before adding copy paper, check whether the paper is dry and clean. Then, straighten the copy paper and stack it neatly and put it into the paper tray with the same size and size. The paper in the tray must not exceed the thickness allowed by the copier. In the south, where moisture is relatively high, some desiccant may be placed in the place where the paper is placed to prevent the paper from being wet and the copier to be used improperly.
10. In the event of an abnormality, the power supply should be cut off immediately and the relevant maintenance personnel should be notified. Abnormal conditions include: overheating, water intake, abnormal noise, etc. If the copier jam should avoid reaching out immediately to remove the paper, make sure that the copier has cooled down before removing the paper.
2. The copier should use a stable voltage. It is recommended to use the socket directly against the wall.
3. The photocopier should be preheated for half an hour before use, which can make the inside of the copier dry, which is beneficial to the effect of copying.
4. Use of the copier According to the instructions for use, read the instructions carefully before copying. Different copying requirements require careful operation according to the function description of the copier.
5. When copying, keep the copier's glass platen clean, scratch-free, and can't have spots such as correction fluid and fingerprints to avoid unclear copying and affect the copying effect.
6. After each use of the copier, be sure to wash your hands in time to eliminate any damage to the body caused by residual dust on your hands.
7. When you find that the effect of copying has a heavy shadow, you may need to clean the lens on the copier.
8. The user should promptly add toner to the copier when the copier panel displays the red light plus powder signal. If the toner is not added in time, it may cause the copier to malfunction or produce powder-impact noise. When adding toner, shake the toner and follow the instructions. Do not use substitute powder (pseudo-powder), otherwise it will cause problems such as flying powder, bottom ash, and shortening the service life of the carrier. Moreover, due to the high rate of waste powder it produces, the actual copy quantity is less than 2/3 of the true powder. .
9. Add paper to the copier. Before adding copy paper, check whether the paper is dry and clean. Then, straighten the copy paper and stack it neatly and put it into the paper tray with the same size and size. The paper in the tray must not exceed the thickness allowed by the copier. In the south, where moisture is relatively high, some desiccant may be placed in the place where the paper is placed to prevent the paper from being wet and the copier to be used improperly.
10. In the event of an abnormality, the power supply should be cut off immediately and the relevant maintenance personnel should be notified. Abnormal conditions include: overheating, water intake, abnormal noise, etc. If the copier jam should avoid reaching out immediately to remove the paper, make sure that the copier has cooled down before removing the paper.
Care Cosmetic Display Rack,Single-Sided Toothpaste Display Stand,Health Product Display Stand,Supermarket Fmcg Stand
Dongguan Display Leader Co., Ltd , https://www.displayonestop.com